On your 2012 BMW Series 1 your only option is the Curt Class I 1-1/4 inch hitch # C11184 which has a max tongue weight of 200lbs and a max gross trailer rating of 2,000 lbs. So, you could potentially haul your two motorcycles on your trailer but there are some things we need to make sure of. First make sure that your vehicle can handle that weight. The hitch may be able to, but you need to confirm your vehicles limits. Usually you'll find it in your owners manual.
Then we need to make... view full answer...
I've linked the instructions for the Curt # C11184, but it shows the tab for the fascia; the tab should be located at the spot where the fascia meets the bumper. You will want to push in on the fascia to get it to disengage from the bumper. If you check out the linked instructions it shows 2 pictures- one of the bumper fascia tab and one where the fascia has been removed and the side plate is installed. The small holes there show where the tabs are going to catch on the bumper plate, so... view full answer...
The trailer wiring harness I recommend for your 2009 BMW 135i is the ZCI kit part # 119250KIT which installs without requiring any splices and comes with a very reliable converter box.
Then for a ball mount you will need the Curt part # C45521 which fits the Curt hitch part # C11184 that fits your vehicle and then for hitch balls you'd want the part # A-82 for a 2 inch ball or part # A-80 for a 1-7/8 inch ball. The coupler of your trailer will tell you which size you'd need if weren't... view full answer...
Yes, you can install the Curt hitch part # C11184 without needing a lift. In the tools required section of the install instructions for this a jack isn't even mentioned. So you'd have no problem installing it without a lift or jack.
I did attach a link the install instructions for you to check out as well for more info. view full answer...
On the CURT Class I 1-1/4 Inch Hitch, part # 11184, for the 2010 BMW 135is the under body panels are at the rear of the vehicle underneath behind the rear fascia. Detailed trimming information is provided in the installation instructions (see link).
All of the hardware required to install the hitch on your BMW 135i coupe or convertible is included.
I have no idea how many of these hitches have been installed on the BMW 135i, but in the last several months we have sold more than 10 of... view full answer...
I can help explain the instructions better for the ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT, but I don't have the details about the wiring on your 2012 BMW 135i so you will need to do some testing with a circuit tester # PTW2992 on your end.
The first thing you need to do is determine what kind of lighting system you have by using the circuit tester to see what happens to the different wires when you use the brake pedal, turn signals, and use your headlights. You can use... view full answer...
I have not had any specific feedback on that vehicle, but having a muffler rattle against a hitch is a fairly common occurrence that is easily repairable.
Because an exhaust system is meant to move on its hangers, it does not sit in a fixed position, and this position can vary a bit from vehicle to vehicle. If you look at the FAQ article I have linked you to, you can see some different strategies like slightly bending the exhaust hangers to provide more clearance between the hitch and muffler. view full answer...
Wiring harness # C59496 is a universal fit type of item that fits many vehicles. Also, there is no standard color code for wiring/function; vehicle manufacturers can use whatever color they want and it frequently changes from model year to model year, and even within the same model year for a given vehicle.
That is why there is a circuit tester included. You have to test the vehicle tail light wiring to determine function and then install the converter accordingly. view full answer...
The Draw Tite hitch part # 75712 that you referenced has been confirmed to fit your 2015 Jeep Patriot so I would recommend it for you.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not have the right rise or drop... view full answer...
The Curt Hitch part # C11184 that you referenced is confirmed to fit a 2013 BMW 128i convertible and would probably take a dealership about an hour to install. We had a customer come back and say it took them 2 hours but a dealership would be able to knock it out much quicker. view full answer...
The Curt Class I Trailer Hitch Receiver with Drawbar, # 11184, will fit your 2010 BMW 128i Coupe. As far as the rattling goes, we have not received any comments regarding rattling. However, if there is rattling, it could be a few things causing the noise.
First, it may not be the hitch, but something that is loose from installing the hitch. If everything is re-assembled correctly according to the instructions (linked below) rattling is less likely. Also, it is important to torque the... view full answer...
The only hitch receiver we have confirmed to fit your 2013 BMW 128i is the Curt Trailer Hitch Receiver part # C11184. Unfortunately, we have not had a chance to install this hitch on a 2013 BMW 128i yet. However, the installation process is fairly straightforward and I will do my best to walk you through the process below.
Before you get started you will need a few tools for installation: 8, 10, and 19mm sockets, 12" extensions, Ratchet, 19mm wrench, Flat Head Screwdriver, Rotary Tool... view full answer...
For your 2012 BMW 1 Series that has factory fixed mounting points on the roof we have the Rhino Rack roof rack part numbers # RRVA118B-2, # RRRLKVA, and # DK328 which is a confirmed fit and would work well.
The Rhino Rack roof racks are high quality racks that don't break the bank like some roof rack brands do so it's one of my favorite racks to recommend. view full answer...
We have had a customer install Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" Item # C11184 on a M model BMW 1 Series before so we can confirm that it fits the M models and it will fit convertibles as well so you are good to go!
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.
Curt... view full answer...
There is a bike rack compatible with your OEM roof rack but there is not an adapter for the now discontinued Rhino Rack Discovery bike rack made for the factory crossbars of your 2011 BMW 128i; the only adapter for this rack is the Fit Kit for Rhino-Rack HD Cross Bars # RBCA003.
For a new bike rack which is going to work on your BMW's roof rack I highly recommend checking out the Yakima FrontLoader Wheel Mount Bike Carrier # Y02103 because its wheel-mount design makes it easy to use, it... view full answer...
I have included a link to the bike racks that are confirmed as a fit for your 2013 BMW 135i Convertible. Of these options, yes the Thule Passage # TH910XT is confirmed as a fit. However, the Thule Raceway # TH9001XT is not considered a fit for your vehicle.
If you will be carrying an alternative, women's, or children's bikes it is recommended to use an adapter bar like the Thule Adapter bar # TH982XT. This will attach to the bike and provide a horizontal cross tube for the bike to mount... view full answer...
The Saris Freedom 2 Bike Platform Rack # SA4412B has a 60 lb per bike capacity so it works with most E-bikes as that's typically more than needed for them. In terms of the bike frame clamp I checked with Saris and they say that it fits all frame styles and sizes. I'd have to see a picture of your bike frame to see if I though it would be an exception to that rule, but in the mean time a better option might be the Thule EasyFold part # TH903202 which has a 65 lb per bike capacit and use... view full answer...
The bumper beam mount studs on the 2013 BMW 128i are part of the factory bumper beam/trunk panel mount assembly. If they are not present then someone on the assembly line wasn't paying attention! The hitch installation should not have been completed if those studs were missing.
The nuts could have been cross-threaded on which would mean that the threads on the studs would have to be re-cut. Regardless to get the properly rated nuts for the hitch you will need # RHK. Enter the hitch number... view full answer...
The Yakima HangOut 2 bike trunk mounted bike rack you referred to, part # Y02637 is compatible with your BMW 1 Series convertible, which would be my recommendation. The KingJoe has been discontinued and is no longer available.
If you'll be transporting women's bikes or bikes with sharply-angled top tubes, you might also consider a frame adapter bar like part # UB01. The bar spans the distance between the handlebar gooseneck and the seat post, which provides a secondary attachment point... view full answer...
Go To Results